This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - sundar
Pages: 1 ... 1005 1006 [1007]
15091
« on: October 06, 2007, 10:04:18 PM »
15092
« on: October 06, 2007, 10:02:57 PM »
This codes is permanent unlock...enjoy
For [T619]
Insert unaccepted sim to phone.
*2767*2878#
(wait 30 secound)
NEXT ENTER
*7465625*638*00000000*00000000#
NEXT ENTER
#7465625*638*00000000#
For
[T209, T309, T509, T809, X100, X495, X660, D600, E780, T319]
2. Input *2767*3855# and enter
3. Input *7465625*638*00000000*00000000#
4. Input #7465625*638*00000000#
5. Input *#7465625# to check the locks....all locks should now be inactive as shown below:
network lock - inactive
subset lock - inactive
sp lock - inactive
cp lock - inactive
sim lock - inactive
activa lock - inactive
phone lock - inactive
auto network - inactive
auto subset lock - inactive
auto sp lock - inactive
auto cp lock - inactive
auto sim lock - inactive
best regards
15093
« on: October 06, 2007, 09:59:07 PM »
Here it is..
*01763*8371# (*01763*VER0#) --- Firmware Version.
*01763*3641# (*01763*ENG1#) --- Enable Engineer Mode hold pwr key to leave then disable. *01763*3640# (*01763*ENG0#) --- Disable Engineer Mode.
*01763*8781# (*01763*TST1#) --- Test #1 (test early wdt looping to dump, need to remove battery from phone)
*01763*8782# (*01763*TST2#) --- Test #2 (test irq dis looping to switch, resets itself)
*01763*8783# (*01763*TST3#) --- Test #3
*01763*8784# (*01763*TST4#) --- Test #4
*01763*8785# (*01763*TST5#) --- Test #5
*01763*87872# (*01763*TST72#) --- Test #72
*01763*8788# (*01763*TST8#) --- Test #8
*01763*5640# (*01763*LOG0#) --- Disable LOG
*01763*5641# (*01763*LOG1#) --- Enable LOG
*01763*4634# (*01763*IMEI#) --- IMEI
*01763*6370# (*01763*MEP0#) --- Disable MEP menu (unlock menu)
*01763*6371# (*01763*MEP1#) --- Enable MEP menu (unlock menu) (go to settings,security,meplocks select insert handset code,default is 0000, allows to check lock status and disable locks only if u have correct code dont try guessing!!)
*01763*63866330# (*01763*NETMODE0#) --- Disable NetMode
*01763*63866331# (*01763*NETMODE1#) --- Enable NetMode
15094
« on: October 06, 2007, 09:56:43 PM »
Repair Videos : Instructions on how to disassemble & assemble phone during servicing. Troubleshooting Guide.
Models:
D750
J220/J230
J300
K300
K310
K320
K500/F500
K510
K550
K600/V600/K608
K610/V630
K700
K750
K800
M600
P990
S700
V800/Z800
W300
W550
W600
W700
W800
W810
W850
W880
W900
W950
Z300
Z520
Z530
Z550
Z610
W710thanks to SeFreakster
15095
« on: October 06, 2007, 09:48:48 PM »
here is the solution of motorola v3x memory is always full even you flash 100% tested by me this day on my two units
here is guide
using your smart moto
1. first repair PDS using testpoint
2. flash your phone for the provided flash file below
3. smile your phone now working perfectlyhere is the logs for my fisrt flashing same of second flashingSmartMoto 2.23
S-Card: maxie Smart-Clip dongle, v 1.24, assigned Smart-Clip: maxie
Europe, initializing... OK
Clip serial: maxie, version: 3.17, initializing... OK
Searching for phone... no phone found
Searching for phone... found S Blank Rainbow POG, getting test interface... interface not found
Switching to flash mode... OK
Reading phone boot version... 3.10
Reading flash id... AMD - S71WS512NE0 (x2)
Phone group: E770,E1000,E1070,V3x,V975,V1050
Hardware IMEI: 35251301xxxxxxx
Security area saved to "PDS for S Blank Rainbow POG 352513010101679 (2).mbk"
Login request... OK
Writing flash section 2 of 2... 100% (114 Kb/sec)
Restarting phone... OK
Searching for phone... no phone found
Searching for phone... found S Blank Rainbow POG
Switching to flash mode... OK
Repair PDS request... OK
Performing PDS repair... OK
Writing flash section 1 of 1... 100% (27.1 Kb/sec)
Please write a corresponding Full_flash file to phone to complete repair
Turning phone off... OK
Searching for phone... found S Blank Rainbow POG, getting test interface... interface not found
Switching to flash mode... OK
Reading phone boot version... 3.10
Reading flash id... AMD - S71WS512NE0 (x2)
Phone group: E770,E1000,E1070,V3x,V975,V1050
Hardware IMEI: 352513010xxxxxx
Security area saved to "PDS for S Blank Rainbow POG 352513010101679 (3).mbk"
Writing flash section 2 of 2... 100% (106 Kb/sec)
Flash completed!
And for the flash files Download here
15097
« on: October 06, 2007, 09:45:04 PM »
**100% Free U8500 Unlock** well, here is a solution to unlock your LG U8500 for free, for thosE who doesn't have Furious Gold, i uploaded drivers, LG Quanlcomm flasher, and pAtched U8500 firmware, only one thing, the patched firmware is japness, so u'll not find any european language except English. u can use com_usb's U8110 cable or any other method me personaly i use ust pro and Z500 cable,just don't flash your phone with LG 7020 cause u may have a dead phone after,well just follow the links firmware:drivers: Flasher:please note this and read it carefuly: when u use the downloader just flash the following files: AMSS Modem Image Media Image Module Image and Flexible Logo and untick all the other boxes, credits goes to imdad_ia Enjoy unlocking
15098
« on: October 06, 2007, 09:38:26 PM »
For VLE6 is here
br
15099
« on: October 06, 2007, 09:14:17 PM »
welcome bro keep on sharing...................
15100
« on: October 06, 2007, 07:30:15 PM »
FORUM BIRTH CERTIFICATE
FORUM NAME: Srimeenakshimobiles Creating Gsmcommunity
DATE OF BIRTH: October 06, 2007, 20:00 GMT +5:30
15101
« on: October 06, 2007, 06:33:56 PM »
welcome once again brother keep on posting..................
15102
« on: October 06, 2007, 04:25:53 PM »
welcome anna keep on posting..................
15103
« on: October 06, 2007, 04:12:28 PM »
welcome bro keep on sharing...............
Pages: 1 ... 1005 1006 [1007]
|
Show Posts