Messages

2281

Nokia Hardware Section / All Nokia Mobile Phones Convert

« on: March 30, 2008, 03:07:14 PM »

2610b CONVERTION


1. Change the rx filter 2610b got it any other phone
2. Dont Flash
3. Write a good pm 2610
4. unlock

2282

Nokia Hardware Section / All Nokia Mobile Phones Convert

« on: March 30, 2008, 03:04:05 PM »

NgageQda to NgageQd
1. Erase flash with special erase
2. flash mcu & ppm to ngageqd
3. replace filters
4. write pm
5. unlock

2283

Nokia Hardware Section / All Nokia Mobile Phones Convert

« on: March 30, 2008, 03:00:59 PM »

8390 to 8310



Jumper resistor is a resistor (not actually a resistor)
with 0 ohm value, usually colored green with 0 markings.

Wire can also be use instead, but must not be very thin
and should be as short as possible. Thin and long wire
will introduce high inductive reactance and will result
to weak received signal.


2. T500 can be taken from 3310 unit. It is located just
above HAGAR, refer to your service manual to easily
locate it. Also take note to its pin orientation during
installation.

Bypassing Z551 with wires is not recommended,
this will weaken the receiver sensitivity due to incorrect
signal phase relationship.


3. Give special attention when installing VCO, improper
positioning will result to no network activity

2284

Nokia Hardware Section / All Nokia Mobile Phones Convert

« on: March 30, 2008, 03:00:10 PM »

6061 to 6060


1. erase whole flash as 6060.
2. flash ur 6061 with 6060 flash pack "RH-73_dp_46_00_ams_sw_4_10".
3. replace 2 filters
4. write pm
5. unlock

2285

Nokia Hardware Section / All Nokia Mobile Phones Convert

« on: March 30, 2008, 02:59:41 PM »

6800a to 6800




1. flash with 6800a to 6800
2. replace filters
3. make jumper near the antenna sw
4. write pm
5. unlock

2286

Nokia Hardware Section / All Nokia Mobile Phones Convert

« on: March 30, 2008, 02:59:14 PM »

6200 to 6610


1. flash phone with nhl-4u (6610) mcu + ppm
2. replace filters
3. write pm
4. unlock

2287

Nokia Hardware Section / All Nokia Mobile Phones Convert

« on: March 30, 2008, 02:55:46 PM »

3220b to 3220


1. change filters
2. upload pm
3. unlock

2288

Nokia Hardware Section / All Nokia Mobile Phones Convert

« on: March 30, 2008, 02:55:32 PM »

3200b to 3200




1. flash the phone with RH 30
2. replace the filters
3. write pm
4. unlock
5. upload pmm for a 3200 phone

2289

Nokia Hardware Section / All Nokia Mobile Phones Convert

« on: March 30, 2008, 02:55:19 PM »

1100b to 1100


1. erase flash
2. flash with 1100(rh18)
3. change filters
4. write pm
5. unlock

2290

Nokia Hardware Section / All Nokia Mobile Phones Convert

« on: March 30, 2008, 02:54:58 PM »

3120b to 3100



1. Flash the phone 3100 but lower than 5.54 (rh19) V4.10 or lower as the    version is suitable for converting
2. change filters
3. write pm  
4. unlock

(sometimes no earpiece write pmm)

2291

Nokia Hardware Section / All Nokia Mobile Phones Convert

« on: March 30, 2008, 02:54:12 PM »

6103b to 6103


No software modification is required
(6103b supports 900mhz)

change 2 filters
then write 6103 PM
unlock

2292

Nokia Hardware Section / All Nokia Mobile Phones Convert

« on: March 30, 2008, 02:53:54 PM »

2651 to 2650


1. Change filters shown in the picture u can use filters from nokia 3100
2. Full flash with 2650 files(Mcu,ppm,cnt)
3. Write a good pm
4. unlock

2293

Nokia Hardware Section / All Nokia Mobile Phones Convert

« on: March 30, 2008, 02:53:37 PM »

6030b to 6030


1. Change the rx filter 6030b got it any other phone(nokia 3100)
2. Full flash with 6030 files(Mcu+ppm+cnt)
3. Write a good pm
4. unlock

2294

Nokia Hardware Section / All Nokia Mobile Phones Convert

« on: March 30, 2008, 02:53:17 PM »

3595 to 3530


1. Flash it to 3530
2. change 2 filters
3. write pm
4. unlock

2295

Nokia Hardware Section / All Nokia Mobile Phones Convert

« on: March 30, 2008, 02:52:58 PM »

All Nokia Mobile Phones Convert

6010 to 3530


1. Back up rpl
2. change flash i.c, 3510i or 3530 flash i.c,then
3. add a ram to it
4. flash it to 3510i,,use rh9 v5.35 flash file
5. change the 3 filters the 850/1900 mhz rx and 1900 mhz tx filter,
6. put a jumper from uem to pa
7. write pm
8. unlock