This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Qmad3
16
« on: March 25, 2008, 12:02:48 PM »
sir with regards to your problem kindly recheck the contacts of your sim ic pins are level to the contacts cause if one messes out its not worth it . or to better sure that they are connect levely . tyr to take all the balls out then ptu it on the board to make it sure. just slightly wiggle it for sure.
17
« on: March 24, 2008, 11:39:34 AM »
sir if your to downgrade the versionin jaf pls always tick the downgrade button . for safe flashing also kinldy visit our download area for the latest updates
18
« on: March 24, 2008, 11:32:43 AM »
3310/ 2100 contact service 100% WIN-98 mcu+ppm flash for your info sir you can do it now xp with the help of user port application .
19
« on: March 24, 2008, 11:30:08 AM »
i use jaf pkey 1.98.44
i have 3310/ 2100 contact service . i flesh this mobile with jaf
but my mobile is on but no network and autometic off-on and display "SIM not valid "
mobile hardware is all ok
full flesh , writte mcu+ppm+pm but not ok . same problem
please detail me about cable 3310 and 2100
please total help me
[email protected] sir use the nok pheonix flasher its very good in this kind of unit. 100% tested by me most of the times
20
« on: March 24, 2008, 11:27:02 AM »
try to do a tp method in smart clip its the only way as of now specially dead unit dont reponds to rsd or ordinary flashing in smart moto.
21
« on: March 24, 2008, 11:24:55 AM »
moto v3 no keapad work please help me with diagram first try to clean out the terminal then resolder the connectors if necessary. last if still not working press firmly on the contacts of the keypad connector to the terminal of the board or put a foam or sponge that fit to the keypads so it connects tightly to the board. most of these problem is due to lose connection of the terminal or worst is the cpu or the neptune ic.
22
« on: March 24, 2008, 11:18:07 AM »
try to replace the lcd bro if not check the led line circiut.
23
« on: March 24, 2008, 11:16:22 AM »
try to repair the pds area bro then do the flash again with your recent version. good luck
24
« on: February 12, 2008, 05:57:08 PM »
nice info bro . very nice................ 
25
« on: February 08, 2008, 01:57:02 PM »
thank you guys for your continuing support . more power to you . and keep up the good work...
26
« on: February 08, 2008, 01:42:46 PM »
i am use jaf+pkey v. 1.98.45 i flesh dct3 mobile 3310 with new version 6.3
after fleshing set faid unlock & fectory reset . but my 3310 on but no network and auto metic power off/on . i try vinring epprom but not working good and this mobile imei is also crupt i am not possible to built new imei.
please help me
[email protected] sir change the audio ic also known as cobba ic then go to nok tools by bphreaks then set it to full factory , input the corresponding imei. unlock it done.
27
« on: February 08, 2008, 01:40:39 PM »
Hai sir!
1600 mobile very heat.....please solution check your uem if not shorted if shorted check your power amp
28
« on: February 08, 2008, 01:33:27 PM »
but not solve this problem
i have 2100 i flesh v 5.49 this same problem
auto on/off after than display SIM card not valid
prakash sir first try to take out the flash ic then put a fresh one then flash it again do all the ui settings. reset phone , factory set edit the imei . just use the old imei . better use the nok pheonix . ok good luck bro.
29
« on: January 12, 2008, 06:15:19 PM »
PROBLEM DOWNLOADING PM FILES?
HERES THE ANSWER TO YOUR PROBLEM
INTRODUCING
"THE ALL IN ONE PM FILES" INSTALLER
JUST DOWNLOAD AND INSTALL(pm files included)
SHARING IS THE BEST WAY TO GAIN RESPECT [/B]
bro can you post this wihout going to other forums. it would be nice to make it easy access to our fellow membes here. thanks and good work ....
30
« on: November 09, 2007, 06:04:38 PM »
how we can flash p910i
thanks sir i would like to clarify what is the history of the unit. because there two flashing method to be done in p910i unit first is just the normal flashing only mcu and modem. and the second is by the pda flashing. in pda flashing there are 3 area pds 1,2,3 . also as a reminder pls becarefull on the verions of the p910i be sure to have a back up first.
|
Show Posts